HomeCorrections
Corrections
If an answer on this site is wrong, tell us below. A person reads every report. If it holds up, we log it here in public and hold the answer until we've fixed or confirmed it. We've logged 17 corrections so far, and all of them are fixed.
Report a mistake
Tell us which page and what's wrong. A link to the maker's page helps, but you don't need one.
What happens next
- A person reads your report and checks it against the maker's own page.
- If it holds up, we add it to the log below and mark the answer as being checked. Any seller link on that answer would come down until it's resolved.
- Once it's resolved, the log says what changed and when, and the answer shows the new date.
Corrections log
Every correction we've accepted, newest first.
| Entry | Page | What was reported | What changed | Status |
|---|---|---|---|---|
| C-2026-017Reported 3 Nov 2026 | /3d-printing/materials/tpu/ | Bambu rewrote its TPU guide, so our TPU answers quoted sentences that are no longer on it. Two of our lines went out of date: that Bambu printers do not support TPU softer than 85A, and that only the AMS HT can hold TPU on the H2D and X1C. | The TPU answers on the A1, A1 mini, P1S, H2D and X1C now quote the guide's current tables and notes. The softness line now names TPU 75A per printer series, and the H2D and X1C answers name the AMS HT or a filament dry box. No verdict changed. | Fixed 4 Nov 2026 |
| C-2026-016Reported 3 Nov 2026 | /3d-printing/parts/bambu-ptfe-tubes/ | The PTFE tubes page said "Bambu Lab counts rolls, not months", while our printer pages quote Bambu's PTFE tube page recommending a new tube every two months. Both are on Bambu's own pages. | The page now quotes Bambu's PTFE tube page (every two months, and a monthly check with abrasive filament) beside its A1 and P1 roll counts, and says Bambu's pages measure it in different ways. | Fixed 4 Nov 2026 |
| C-2026-015Reported 3 Nov 2026 | Bambu Lab P1S | The P1S and X1C PTFE tube answers gave the tube above the toolhead as 2.0 mm inner diameter. Bambu's PTFE tube table now says 2.5 mm inner and 4.0 mm outer, as does our own PTFE tubes part page. | Both answers now say 2.5 mm inner and 4.0 mm outer and quote the current table. We searched the site for the same figure and found no other instance. | Fixed 4 Nov 2026 |
| C-2026-014Reported 12 Oct 2026 | /3d-printing/parts/bambu-tpu-85a-90a/ | The TPU 85A / TPU 90A page and the finder linked both grades to both of the A1's answers. As a result the finder could show TPU 85A as usable on the A1 and offer "Get this part", although Bambu's page says TPU 85A is not for A Series printers. | On the A1, TPU 85A now carries Bambu's A Series warning with no Get this part, and TPU 90A keeps its nozzle and AMS limits, each quoting Bambu. The P1S answer was already right. We checked every other part for the same fault and found none, and the build now fails if one version ever gets two answers for the same printer. | Fixed 12 Oct 2026 |
| C-2026-013Reported 11 Oct 2026 | Bambu Lab A1 mini | The carbon and glass-fibre filled answer for the Bambu Lab A1 mini had the same problem as the A1 (C-2026-012): it said "Not recommended" from the A1 mini product page only, while Bambu's filament guide says the opposite for PLA-CF and PLA-GF on open-frame A Series printers. | The answer now shows "Conflicting information" with no verdict, quotes both Bambu pages, and states the hardened steel nozzle requirement. We also re-checked the P1S answer: its product page sets a condition (an extruder and hotend upgrade first) rather than contradicting the filament guide, so it is unchanged. | Fixed 11 Oct 2026 |
| C-2026-012Reported 11 Oct 2026 | Bambu Lab A1 | The carbon and glass-fibre filled answer for the Bambu Lab A1 said "Not recommended" from the A1 product page only. Bambu's filament guide says the opposite for PLA-CF and PLA-GF on open-frame A Series printers, so Bambu's own pages disagree. | The answer now shows "Conflicting information" with no verdict, quotes both Bambu pages, and states the hardened steel nozzle requirement that both pages share. | Fixed 11 Oct 2026 |
| C-2026-011Reported 10 Oct 2026 | Bambu Lab X1 Carbon (X1C) | Two TPU notes went further than Bambu's words. The advice to feed TPU from the external spool holder had no quote behind it (on the A1, A1 mini, P1S, H2D and X1C pages), and the X1C page said the AMS HT can hold TPU without a quote showing the AMS HT can be connected to the X1C. | The spool holder advice is removed. The AMS HT note now quotes Bambu's AMS HT page, and the X1C note adds the parts Bambu says you need to connect one. No verdict changed. | Fixed 10 Oct 2026 |
| C-2026-010Reported 10 Oct 2026 | Bambu Lab H2D | The H2D PETG answer showed a plain yes while listing a limit (do not print PVA and PETG at the same time on the two hotends), and the limit had no quote beside it. | Changed to a verdict with limits, with Bambu's H2D filament configuration quote added as the source. A build check now stops a plain yes from carrying limits. | Fixed 10 Oct 2026 |
| C-2026-009Reported 10 Oct 2026 | Bambu Lab A1 | Three TPU limit notes were not backed word for word: the 85A note quoted the A1 row without the table headings, the AMS HT feeding detail and the TPU for AMS exception had no quote on the H2D and X1C pages, and the hardness note left out Bambu's word "currently". | Quotes now include the table headings and the AMS HT and TPU for AMS sentences from Bambu's TPU guide, and the note says "currently". No verdict changed. | Fixed 10 Oct 2026 |
| C-2026-008Reported 9 Oct 2026 | Bambu Lab H2D | The H2D PVA answer was marked as having limits but did not list the limit. | The limit is now listed: do not print PVA and PETG at the same time on the left and right hotends. The verdict did not change. | Fixed 9 Oct 2026 |
| C-2026-007Reported 9 Oct 2026 | Bambu Lab P1S | The P1S source quote ran together two columns of Bambu's store table (P1P and P1S), and the nylon and polycarbonate answers were marked as having limits without stating them. | Quote cut to the P1S column only; the nylon and polycarbonate limits are now stated. The verdicts themselves did not change. | Fixed 9 Oct 2026 |
| C-2026-006Reported 9 Oct 2026 | Original Prusa MK4S | The flexible (TPU) answer for the MK4S answered a plain yes without Prusa's warning that automatic filament change might not work properly with flexible filaments. | Changed to a verdict with limits, with the warning stated and Prusa's flexible-materials guide quoted. | Fixed 9 Oct 2026 |
| C-2026-005Reported 9 Oct 2026 | Bambu Lab X1 Carbon (X1C) | The TPU answer for the Bambu Lab X1C answered a plain yes without the limits in Bambu's TPU guide: the AMS, AMS lite and AMS 2 Pro cannot feed ordinary TPU. | Changed to a verdict with limits, with the limits stated and the TPU guide quoted as a source. | Fixed 9 Oct 2026 |
| C-2026-004Reported 9 Oct 2026 | Bambu Lab H2D | The TPU answer for the Bambu Lab H2D answered a plain yes without the limits in Bambu's TPU guide: the AMS, AMS lite and AMS 2 Pro cannot feed ordinary TPU. | Changed to a verdict with limits, with the limits stated and the TPU guide quoted as a source. | Fixed 9 Oct 2026 |
| C-2026-003Reported 9 Oct 2026 | Bambu Lab P1S | The TPU answer for the Bambu Lab P1S answered a plain yes without the limits in Bambu's TPU guide: the AMS, AMS lite and AMS 2 Pro cannot feed ordinary TPU. | Changed to a verdict with limits, with the limits stated and the TPU guide quoted as a source. | Fixed 9 Oct 2026 |
| C-2026-002Reported 9 Oct 2026 | Bambu Lab A1 mini | The TPU answer for the Bambu Lab A1 mini answered a plain yes without the limits in Bambu's TPU guide: the AMS, AMS lite and AMS 2 Pro cannot feed ordinary TPU, and the A1 series cannot print TPU 85A. | Changed to a verdict with limits, with the limits stated and the TPU guide quoted as a source. | Fixed 9 Oct 2026 |
| C-2026-001Reported 9 Oct 2026 | Bambu Lab A1 | The TPU answer for the Bambu Lab A1 answered a plain yes without the limits in Bambu's TPU guide: the AMS, AMS lite and AMS 2 Pro cannot feed ordinary TPU, and the A1 series cannot print TPU 85A. | Changed to a verdict with limits, with the limits stated and the TPU guide quoted as a source. | Fixed 9 Oct 2026 |